Flash 2 Pass Motorcycle Garage Door Opener is a complete kit that includes the patented transmitter, receiver, all installation hardware and easy do it yourself instructions for ANY motorcycle, scooter or other vehicle.

Works with virtually any garage door opener manufactured since 1982. No Remote to get lost or stolen, No batteries to ever replace, Simple 2-Wire installation, Waterproof, Digital Rolling Code Security, Single Receiver works with up to 6-Transmitters, Works with virtually any garage door opener since 1982. Additional transmitters available seperately and are shown as Related Product on page.

Motorcycle Flash2Pass Motorcycle Transmitter is a small radio frequency device that mounts inside your motorcycle. Measures 2" x 2” x ¾”. Wires stay attached with Posi-Tap connectors to the headlight high beam positive wire and to the ground wire. The Flash2Pass™ transmitter is non-polarized so you can attach either wire to the headlight wires.

The Flash2Pass™ receiver is designed to replace the pushbutton inside your garage. If you have additional functions on your pushbutton that you would like to keep, the receiver can be installed next to your original pushbutton and “piggybacked” to it.

The Flash2Pass™ transmitter and receiver are packaged as a set that is pre-programmed at the factory, or they are available individually. For instance, if you had a two-car garage with one large door for both bays, you would buy one set and an additional transmitter. The additional transmitter would be installed in the second vehicle and the receiver programmed to accept it.

Say you had a vacation home with a garage door opener. You could get an additional Flash2Pass™ receiver for it and then program your motorcycle, scooter or car to it. That way, you wouldn’t have to remember to bring the remote with you. It will always be at your fingertips…both at home and on vacation.

Now, if you live in a gated community and the community installed the F2P Integrated Control Access System, you would be able to access the community gate, and your individual garage. We call this the “gate to garage” concept. Also if you worked in a place that had some sort of parking control and the F2P ICAS were in place, you again could use your Flash2Pass™ transmitter to gain access, assuming you were authorized and/or programmed into the receiver.

You know your garage door remote that you have to fumble for everytime you get home. Maybe it’s inside your fairing pocket, inside your saddlebags or in your purse or jacket pocket or maybe it just drove away in the other car or motorcycle your spouse was driving.

You know what the battery looks like, too, you replace it every year or so. It’s a nine-volt, or is it two AA’s? You better check before you buy new ones…

You might even worry about somebody swiping it and using it to get into your house.

We solved these problems by integrating the activation of your garage door opener remote into the high beam switch of your turn signal lever.

      A double flash of your motorcycle headlight high beams opens or closes your garage door

      A small one time investment gets you the maintenance free system

      No remote transmitter to get stolen or lost

      No battery to buy or replace…Flash2Pass™ gets its power from your car

      Digital encrypted signal and rolling code technology for ultimate security

      Quick and easy do-it-yourself installation

      Up to six transmitters may operate a single receiver

Motorcycle Transmitter Installation - Depending on the motorcycle, the easiest way is to remove the headlight from the bucket as if you were changing the bulb, and connect the transmitter. Then just tuck the transmitter into the bucket or fairing if applicable and reinstall the headlight. Again, this may not be applicable to every installation, but it is a general rule of thumb.

Receiver Installation - Motorcycle Flash2Pass Receiver is even easier to install. There are two wires that go from the garage door opener motor to a pushbutton on the wall that you use to open the garage door from the inside. After disconnecting the power to the garage door opener, you will remove the pushbutton from the wall, undo the two wires from the back and attach them to the Flash2Pass receiver, and attach the receiver to the wall. Turn the power back on, and that's it!

If your current pushbutton console has functions other than to open the door, like light and lock switches, you can still keep those functions by using "jumper" wires from your current console to the Flash2Pass receiver. Complete instructions are included with every set and separate receiver.

 Additional receivers may be installed elsewhere and programmed to your Flash2Pass™ equipped motorcycle, scooter or other vehicle.

Fits ANY motorcycle, scooter or car and works with virtually any garage door opener manufactured since 1982